This article deals with the deposit policy banks. Determined that the savings accounts are the most diverse and the basis for their classification is the criteria of the sources of contributions, their intended use, the degree of profitability. The focus is on the definition of criteria, goals and objectives. This article can be viewed as the formulation stage for further research in the master's thesis.

In this article issues of efficient use of ferroalloys production waste to save costs are considered; energy efficiency of agglomerate production is calculated; sintering heat balance data are presented by a case study of Aksu Ferrolloy Plant. According to the annual economic benefits calculation the folowing results are obtained: due to аglogases recirculation, fuel saving is 1334.5 t.o.e.; due to reheating it is 1491 t.o.e.; due to installation of thyristor converters to the unit the annual energy saving is 1714000 kWh. Thus, it is identified that besides energy-efficiency measures during recycling of solid and gaseous wastes, the use of agglomerate increases IPF electric furnaces performance as well, decreases specific energy and reducing agent consumption which means the prime cost of finished products will be reduced.

One of the directions of energy saving is the application of heat pumps by means of which it is possible to use low-potential, usually waste heat. The question of the possibility of using heat pumps in thermal power plants is considered in the present article. Also a diagram of possible use in thermal power stations of low-grade waste heat with heat pump installation is presented in the article.

This article contains the most optimum temperature requirements for hydrogenation reaction by Pd- PEG/ZnO catalyst. Works of some foreign authors have been investigated due to to create catalysts for the preparation of which energy consumption will be negligible and the catalyst activity will remain the same.

This article considered the essence of public policy, features of competitive economy and priority directions of macroeconomic politics of Republic of Kazakhstan. For providing of competitiveness of national economy certain seven long-term priorities that based on open market economy with the high level of foreign investments and domestic saving. Also given socio-economic description of the Pavlodar area and role of region in a country.

This article discusses the use of ash and slag waste such as ash or slag boilers and thermal power plants of Pavlodar region. We describe the main source of energy today. Produced by laboratory analysis of the composition of the ash. A basic installation for the processing of the ash. It presents the possibility of using fly ash in building materials industry.

The approach which was proposed earlier for composite materials strength prediction using contact angle measurements was applied for graphite laminated materials. It was shown that the calculation of the work of adhesion to polar and non-polar model liquids can be applied to the choice of polymer binder.

The variants of the use of carbon as a heat-generating material in the agro-industrial complex are highlighted. This will significantly save energy, improve the environment, reduce the cost of operation, repair and maintenance of buildings and structures.

Evaluation of the output of lime is made for three options for the use of Ferroalloy gas: when you use the physical heat of the gas; when using the chemical energy of the gas and the location of the reactor after scrubbing; when sharing of sensible heat and chemical energy of the gas. As a result of the calculation of the expected yield of lime, it was found that the use of Ferroalloy gas for the production of lime can fully provide or at least compensate for the deficit of lime in the production of steel. The technology of calcination of limestone with Ferroalloy gas is presented in the form of a cycle synchronized with the smelting of steel, including, in accordance with the gas outlet from the layer and their alternation with pauses of inter-blowing periods. The preliminary technological characteristics of firing obtained as a result of theoretical analysis are used for further experimental and theoretical studies.

This article describes the effect of pre- and probiotics on the digestibility of feed by newborn calves. The calves of the experimental groups had a high growth energy, which was reflected in the absolute growth rates and their development.

The possibilities of using controlled transformer-type shunt reactors at power grid substations to optimize the transmission mode are considered. The laws of voltage regulation, providing the mode of natural power and reduction of active power losses in the electrical system, are highlighted. Key words: energy complex, controlled transformer-type shunt reactor, voltage stabilization, thyristor voltage controller, control winding.

Nanotechnology is a field of fundamental and applied science and technology dealing with a combination of theoretical substantiation, practical methods of research, analysis and synthesis, as well as methods for the production and application of products with a given atomic structure through controlled manipulation of individual atoms and molecules. In the Address of the President of the Republic of Kazakhstan to the people of Kazakhstan Strategy "Kazakhstan-2050" New political course of the state, the leader of the nation, N.A. Nazarbayev, defines 10 tasks that Kazakhstan faces, one of which is the transition of Kazakhstan to the third industrial revolution. Nanotechnology is one of the branches of the industrial revolution. In the modern world, over the past few years, there has been a rapid development of nanotechnology. The peculiarity of nanotechnology lies in the possibility of their application in an unlimited sphere; therefore they are the basis for a completely new technological order of the economy. Сonsequently, its development in the country is regarded as a particularly important sphere of science. Usage of nanotechnology products will save on raw materials and energy consumption, reduce emissions to the atmosphere and, as a result, will contribute to sustainable economic development.

During the preparatory activities for the preparation and conduct of the KShU, the civil defense plans for peace and wartime were adjusted and clarified, the calculations of forces and resources for conducting emergency response activities were refined and their readiness checked. Checked the combat readiness of the units taking into account work in extreme conditions and the provision of personnel with equipped interchangeable clothing. Additional briefings have been organized on compliance with safety measures for fighting fires and performing emergency rescue operations. Autonomous sources of energy supply, stocks of material and technical, food reserves were checked. In general, the forces and facilities of the units of the Service are on daily round-the-clock alert duty and are ready to meet the set tasks for eliminating emergencies and situations at the first alert.

The article is devoted to solving the optimization problem of finding an energy-efficient mode operation of one of the types of energy-intensive industries with the properties nonlinearity, inertia, and isolation. An optimization model based on a genetic algorithm is considered as a solution method. Moreover, the calculation of the fitness function for the selection of chromosomes is proposed to be calculated on the basis of fuzzy logic

In the article presents the results of studies on the effect of temperature and pressure on the chloride sublimation of zinc and lead from converter dusts of steel production. Currently, an objective necessity is the development of dust utilization technologies for converter steel production, with its further use in production and production of by-products. The use of dust allows not only to save natural raw materials, but also increases production efficiency and improves the environmental situation. The content of non-ferrous metals in dusts makes it difficult to process and use them in agglomeration or in blast furnace production, while the iron content in converter dusts (sludges) makes it possible to use them as promising metallurgical raw materials. Therefore, for a more complete processing of dusts, extraction of non-ferrous metals from them is proposed. The purpose of this work was to determine the possibility of extracting zinc and lead from sludges of the converter production by the method of chloride sublimation. We used dust containing: 86,3 % Fe2O3, 3,5 % FeO, 0,9 % Al2O3, 1,6 % CaO, 0,9 % MgO, 1,1 % MnO, 0,8 % SiO2, 4,4 % ZnO, 0,5 % PbO. The study was conducted in the temperature range 200-1600 degrees C and pressures of 0,01; 0,1 and 1 bar based on a complete thermodynamic analysis using the HSC – 5.1 software package. Finnish metallurgical company Outokumpu, based on the principle of minimum Gibbs energy. According to the results of the studies, it was found that, at normal pressure, lead chloride sublimationbegins at a temperature of 600 degrees С, and zinc - at 900 degrees С: a decrease in pressure to 0,01 bar reduces the temperature to 500 degrees С and 700 degrees С, respectively; lead chloride sublimation under equal conditions is more complete than zinc; To achieve zinc chloride distillation at the level of 90-96 %, the process must be carried out at 1145-1200 degrees С and pressure from logP = -2 to 1,2 bar, while the degree of lead chloride distillation is 99,8-100 %.

This paper presents the results of the influence of ultrasonic treatment in the cofermentation of the cattle manure mixture (cattle) with the leaven from the rumen of ruminants on the process of biogas production. Anaerobic digestion was carried out in matinence periodic operation at the mesophilic temperature of 38 C ̊. As a substrate, a mixture with a content of 70 % cattle manure and 10 % leaven from rumen of ruminants was used. Treatment with ultrasound of the mixture was carried out at an intensity of 10 W/cm2 and an amount of input energy of 9350 kJ/kg of dry matter (DM), which completely eliminated the processes of stratification and sedimentation. Decomposition of organic matter (OM) in the periodic regime with the enzyme and ultrasound treatment occurred within 8 days, the usual substrate during this time OM decomposed 3.0 times less (only 14 %). The process of fermentation of methane in continuous and periodic modes treated with ultrasound, as at other temperatures, was stable, as can be judged by the values of volatile fatty acids (VFA) Volatile fatty acids (VFAs), alkalinity, pH, and biogas. The energetical efficiency of methane fermentation is estimated by comparing the volume of fuel (biogas) and heat consumption for technological needs. As shown by the comparison of efficiency of different regime, the largest amount of commercial energy in the form of biogas was obtained in the mode of joint fermentation of a mixture of cattle manure (cattle) with a ferment from the rumen of ruminants treated with ultrasound – 3 times more than without treatment (space).

The article analyzes the state and problems of cluster development in the real sector of the region based on the materials of the Pavlodar region. The main problem of innovative development of the Pavlodar region, as well as in all regions of Kazakhstan, in general, is the lack of innovative activity of enterprises, which is reflected in the volume, frequency and efficiency of their innovations. At the same time, most of the enterprises belonging to the real sector of the economy have sufficient resources for the development of innovative activity. However, the prospects for their interaction with enterprises in other sectors and sectors of the economy for the purpose of technology transfer are insignificant, which, in general, doesn’t meet the principles of balanced spatial development of the territory formulated by the program for the development of territories of the Republic of Kazakhstan until 2020. One of the ways to solve this problem is formation and development of a cluster approach and interaction of business entities. The article assesses the efficiency of the cluster’s functioning as an institution of regional development. On the example of the metallurgical cluster of Pavlodar region, the main ways and methods of forming cluster initiatives in the regional economy are considered, a SWOT analysis of the development of the metallurgical cluster of the region is given, and its main problems are identified; identifies priority directions of clusters’ development (metallurgical cluster, including the production of final products, the cluster of railway engineering, agri-food cluster), the realization of which in the region could create the conditions for the emergence and full development of a number of new highly specialized sectors such as cluster chemistry, cluster of road and construction machinery, transport logistics cluster, cluster of modern production technologies and engineering, cluster of manufacturing components for machinery and equipment and cluster of industrial electrical engineering and equipment for power engineering. The authors also noted that the realization of regional development strategies of cluster initiatives can potentially lay the foundations for clusters “future days”, such as: cluster of resource efficiency and environmentally processing, the cluster of new energy, the cluster of innovative medicine, tourism and recreational cluster.

Main problem: Presence of acidic chemicals such as carbon dioxide and hydrogen sulphide, composition of production fluids triggers corrosion. Corrosion in oil and gas industry leads to deterioration of equipment since most of equipment is made of metal alloys. Application of inhibitors is one of the corrosion mitigation methods that needs to be controlled because it is important to identify optimal concentration of the chemicals in production fluids.Residual chemical analysis plays an important rolein identifying the appropriate dosage of corrosion inhibitors and its correction. It is imperative to find the most optimal concentration of amines due to the fact that both overdose and underdose could lead to equipment deterioration. The chemical analysis is hindered by complexity of mixtures that are applied in petroleum industry. Purpose: The main purpose of this article is to find out the most effective method of residual chemical analysis for inhibitors used against sweet and sour corrosion by studying and analyzing corresponding literature review. The analysis should be carried out with robust, sensitive, and accurate instrumentation. Methods :Theoretical study of composition and mechanism of amines used in oil and gas industry as corrosion inhibitors and selection of appropriate instrumental analytical techniques for the residual analysis. Results and their importance: After careful studying and consideration of modern instrumental analytical techniques the most optimal and efficient method in terms of robustness, time saving and cost was selected. Ion chromatography is an adequate method to carry out residual chemical analysis for amines that are used as inhibitors in oil and gas industry to prevent sweet and sour corrosion.

When solving project tasks, it is necessary to take into account the maximum number of possible solutions that contribute to the efficiency of the object. When analyzing the activity of multifunctional objects, such solutions are all the more important, since they allow, taking into account the specific features of the object, to make the most rational design decision, especially if these solutions are associated with the ability to solve environmental and energy-efficient problems. The decisions made can take into account both the operation of the object itself and the infrastructure that provides the solution with the necessary engineering solutions. The most difficult thing in making project decisions is to systematize the studied situations and analyze informative sources. Systematization of methods of pre-project analysis, generalization of the experience of project work on the example of designing a roadside service object. Wepropose forms that facilitate the structuring of information sources, as well as logical tables that give an idea of the specifics of the choice of positions and directions that allows quickly come to an understanding of how to implement project tasks. Awareness of the methods that allow organizing the logic and sequence of design processes in design and architectural design allows the author to identify the most important problems from his point of view and fit them into the range of design tasks. The search for answers to these problems is formed by ways of structuring information and displaying it in pictorial structures, where the word takes on the meaning of a specific symbol, in a chain of connections that determine the understanding of the integral process of functioning of the future object, taking into account all aspects of its activity.

Main problem: in the history of mankind there are many examples when the question of national interests remains unresolved. The category of "national interest" has firmly entered the modern political and scientific spheres of all countries of the world. Regardless of the level and nature of development, any country has certain national interests on which it should focus. Undoubtedly, these are economic interests. Future populations, whose state and national goals are not clearly defined, may be unplanned and fragmented. Consequently, it may be violently imposed on a foreign socio-political structure. Historical experience shows that the staging of specific problems can have a negative impact on the application and implementation of the necessary measures to prevent possible mistakes, to strengthen the security of the country. In order to make this article complete and exhaustive, it is necessary to pay attention to the concept of "concept", which reflects the active attitude of people to the surrounding world as the most important category. Purpose: The purpose of the study is to analyze the concept of economic security as a state-legal institution in the Republic of Kazakhstan. Methods: The following methods are used in the article: comparative-legal, system-structural, as well as the method of systematic analysis of needs. Results and their significance: Necessity, personal interests are one of the key links in the study of the essence of the social state. After all, the rule of law in its norms must express the social interests of man in life. These categories are intended to identify the indirect causes of social actions that lead to changes and additions in various spheres of public life. Every country has its own attractions. Interests are different. And the social group, and the team, and the individual combine their actions with their interests. Man interacts with it through its goal, which determines the interests of the environment. Therefore, at the level of common consciousness, a great value of interest is determined by individual actions and actions of people, as well as by mass historical events and phenomena. By looking at this issue in detail and analyzing its basic principles, we define the concept of economic interest. In order to ensure the economic security of Kazakhstan, it is necessary to rely on its own scientific and technological development, human and natural resources, that is, to decide on management in favor of domestic producers and ensure capital investment in priority sectors of the economy.

The article examines modern technologies that contribute to the implementation of creative design ideas, based on the analysis of modern lighting technology and energy saving factors. It is hypothesized that the goal of modern design in this article is defined as the creation of new space and values, through the renewal of the human environment. The basis for confirming this hypothesis should be the justification for the use of lighting technology and electronicsin solving conceptual and artistic design problems. The scientific research is based on the methodology for making design decisions and ways to open new ways for the implementation of creative imagination and new conceptual solutions of the designer, on the example of designing the interior of a cafe. The author considers and substantiates such terms as intelligent space, interior as a process, integrated lighting systems, informatization of interior space, new methods of decoration, etc. Examples of analysis of design situations from are given the point of view of functional tasks, classification of requirements when making design decisions is substantiated. Lighting technologies in the interior are viewed as a tool that solves a whole range of tasks that combine aesthetic and technological principles of interior shaping. Modern technology is seen as a designer's tool that should be used to understand the role of design as a conduit of scientific advances and innovative technologies to the consumer environment.

The article presents the results of implementing a quality management system at the enterprise. The study and analysis of the international standard ISO 9001:2015, as well as sanitary and epidemiological requirements for production control were carried out. The main requirements and rules for the implementation of input, operational and output control of products at enterprises at all stages of the product life cycle were identified and presented. In addition, it was determined what requirements must be met by enterprises to implement a quality management system. It is important to note that this work is necessary at the enterprise, as it has the following advantages: by improving product quality, product sales increase, the level of management of the enterprise and personnel increases, and cost savings are realized at the stages of development, production and operation. It follows that to implement a quality management system, it is necessary to set the following tasks: describe the company's processes, develop performance criteria and evaluate processes, develop the necessary documented information, implement documentation in all departments, familiarize them with the quality policy and goals, conduct timely internal audits for further SWOT analysis, and conduct an assessment by an external auditor in order to obtain a certificate of compliance. An important step in quality management is that the organization should not eliminate nonconforming results of processes, but should identify potential nonconformities, assess the risk with the preparation of a Protocol, plan and implement actions to reduce risks. Difficulties may arise: lack of understanding by the staff of the need to implement a quality management system, lack of a clear vision, mission, lack of complete information on processes, lack of quantitative and qualitative evaluation criteria, quality is defined as the quality of products, not as the quality of processes, resources, lack of monitoring of customer satisfaction. It is possible to overcome these difficulties only with the implementation of the quality management system according to ISO 9001, since the requirements prescribed in the international standard are a real tool for improving the efficiency of the enterprise, which will help bring the organization to a higher level of development.

The main problem: This article is devoted to the key problems of the fuel and energy complex of the Republic of Kazakhstan: 1) lack of production capacity to meet the growing demand for energy and fuel from the economy and the population. Increased demand for electricity and heat, which will require the commissioning of new generating capacities.There is already a shortage in the fuel markets. Modernization and bringing the existing oil refineries (hereinafter referred to as refineries) to full capacity will not allow providing the domestic market until 2030; 2) the export orientation of raw materials, the dependence of the economy on the export of energy resources. In order to attract technology and investment in the oil and gas and nuclear industries, agreements on the extraction of energy resources were concluded with international export companies. In the medium term, Kazakhstan may face a shortage of oil for domestic refineries, if measures are not taken to stimulate its refining within the country. The uranium mined is fully exported; 3) high energy intensity of the economy, low level of energy efficiency. There is a high potential for increasing the efficiency of energy use both in the electric power industry and fuel production, and at the level of final consumption – in industry and housing and communal services; 4) decrease in the replenishment and quality of the resource base in the oil and gas, coal and nuclear industries; 5) low environmental friendliness of technologies used in the fuel and energy complex. Purpose: The purpose of the article is to reveal the problem in the field of ensuring the fulfillment of international obligations between different countries and their own energy sufficiency by gradually changing the structure of energy production. Methods: Studying the experience of increasing the efficiency of the use of energy resources and energy saving as a priority of the state policy of the country. Analysis of production capacity with a constantly forecasted shortage of primary energy resources and insufficient growth of capacity for the production of electricity and heat. Consideration of the possibility of compensating for the shortage by saving energy resources, increasing tariffs for energy carriers, as a stimulating factor for their effective use. Results and their significance: The results of this article will reflect the problems of energy, as the most important driving force of global economic progress. The well-being of the people depends on the state of the country's energy sector, therefore there is an urgent need to solve the emerging problems. The global energy problem is, first of all, the issue of stable and efficient supply of fuel and energy to mankind. Today, the energy sector of Kazakhstan is focused on fuel resources, since the country is provided with hydrocarbons and other energy resources. About 72 % of electricity in Kazakhstan is generated from coal, 12,3 % from hydro resources, 10,6 % from gas and 4,9 % from oil. Thus, the four main types of power plants generate 99,8 % of electricity, while alternative sources account for less than 0,2 %.

Currently, the problems of environmental safety are facing society. The industry develops every year. In this critical economic situation, the oil industry is a stimulant for the economic sector in Azerbaijan. The level of development of this industry is also relevant due to other reasons: sociological, technological and features of the economy of Azerbaijan. The production activity of oil processing, concentrating harmful substances and energy, is a source of man-made danger and pollution of the natural environment. The risk management process mainly consists of three stages - risk safety analysis, risk assessment, which is carried out in comparison of calculated and actual risk levels, the so-called acceptable risk levels and the adoption of appropriate regulations and management decisions. One of the factors that should be taken into account when assessing risk and safety is to determine the necessary costs. Since these costs are paid directly to the company, they try to minimize them as much as possible, which reduce the accuracy of risk assessment. One of the objectives of the study is to determine the optimal value of the necessary costs. It is established that the less reliable the method, the lower is the cost of its implementation. The methodological basis of the work was scientific works on these problems of scientists-economists, mathematicians on safety and risk assessment at industrial enterprises. When developing the presented methodology, computational algorithms developed by Dow Chemical were used. This company has collected a large volume of material on accident statistics, taking into account damages. Based on the obtained and experimentally verified data, a system of indices has been developed, an assessment of various indicators for qualitative and quantitative risk assessment of oil refineries. The analysis of the technogenic danger of oil refineries makes it possible to determine ecological and economic losses and choose rational possibilities of acceptable risk. The required costs, depending on the level of risk, are determined based on an increase in the accuracy of calculating the probability of occurrence of the cause of risks. The article examines the relationship between the expected level of risk and economic losses during oil refining in separate technological units, which allow determining the required level of risk and the expected economic damage.

There have been different approaches to the phenomenon of ellipsis in both world and modern Azerbaijani linguistics. Although ellipsis is widely studied between the sides of compound sentences, but we believe that taking the wider and more diverse evolutionary processes in composite sentences, especially in complex sentences into consideration the fact of ellipsis in these constructions needs to be studied more deeply. The article provides detailed information on the characteristics of the formation of elliptical shapes of subordinate compound sentences. As you know, a subordinate compound sentence consists of two components: a main and a subordinate sentence. The ellipsis observed in a subordinate compound sentence does not manifest itself in the form of omission of any part of a sentence as in a simple sentence, but in the context of omission of the whole mai or subordinate sentence. Although the phenomenon of ellipsis can manifest itself in both components, the article deals with the ellipse observed in the main sentence. The article also notes that the phenomenon of ellipsis is naturally more characteristic of dialogic speech. Because this event occurs not as a deliberate, pre-planned form, but as a result of the natural regularity of language. It is clear that the basis of dialogic speech is question and answer sentences. Some of the question and answer sentences, in turn, form the components of a subordinate compound sentence, forming a dialogue unit. In some dialogues with such a construction, the phenomenon of elliptism manifests itself in the question sentence and in others in the answer sentence. It also provides detailed information on the role of many factors in the emergence of this language fact, in particular, the tendency of the language to save. The article also reflects and compares the views of world linguists on the phenomenon of ellipsis. The fact of the language which is dealt with is substantiated by concrete examples.

An analysis of the mechanical, chemical and pyrogenic impact of the Baikonur Cosmodrome on the environment showed the presence of man-made impacts of the first stages (FS) used on the ecosystems of the impact zones (IZ). This article presents the concept of a controlled landing of spent launch vehicles with liquid rocket engines (LRE) in the expected zones of damage to the ecosystems of the area while maintaining the energy-optimal launch scenario of the launch vehicle. Purpose of the article - development of effective technologies for reducing the anthropogenic impact during launches of promising rockets from the Baikonur Cosmodrome based on theoretical and experimental studies of innovative technologies: reducing the area of impact of parts from launch vehicles; fire and explosion safety, no danger of rocket launchers; controlled descent of used first stages; To solve the problem, it is proposed to create an additional IASM, which will be included in the environmental management system of the Baikonur Cosmodrome. Possible design solutions are proposed based on the evaporation of untreated liquid waste from the tanks of separated parts, their fire and explosion safety, and the use of the obtained vapor-gas mixtures for controlled unloading of separated parts while moving along the landing trajectory to the optimal area. The authors of the article have developed evaluation criteria that characterize the main environmental indicators of the studied areas: fire hazard, soil cover and impact on vegetation are studied for inclusion in the IASM. There are objective requirements and basic rules for the creation of HIASM, which is an integral part of the environmental management system of the cosmodrome.

Main problem: The use of waste heat is most often solved by installing heat exchangers, but this is not effective when the temperature of this heat does not exceed 10-15 0 C, in which case this heat can be used using a heat pump. Where can I get this heat? Almost any enterprise needs cooling of any equipment elements or substances – working fluids; the heat received from them can be sent to a heat pump and used here at the enterprise. Purpose: Consideration of the possibility of using the heat of cooling water from the pump CNS 60-165 and the proposal of a new scheme with the installation of a heat pump that uses this heat. Methods: This is achieved due to the fact that it is proposed not to discard the heat, but after its use in the heat pump evaporator, transfer it to the heated medium - water, which is then sent to the shower cabins of the enterprise. Since the showers are located in the same room, the cost of transporting heat and losses will be minimal. Methods: In the course of the research, the possibility of using the waste heat of an industrial enterprise for using it here at the enterprise for the purposes of hot water supply was considered. For these purposes, it is proposed to install a heat pump, thanks to which the thermal potential increases, which makes it possible to fully use the received heat. Results and their significance: As the experience of foreign countries has shown, heat pumps can be widely used in many industrial enterprises, and in conditions of increased competitiveness, in order to reduce energy costs and the cost of manufactured products, install heat pumps to utilize excess heat, for example, process water, which is available in many production allows you to have a significant economic effect.

The article examines the emergence and functioning of the Soviet institutions of power in Kazakhstan during the period of "war communism". On the basis of archival materials and published works, the author analyzes the activities of Soviets and revolutionary committees. The purpose of the article is to study the main trends and features of the development of local government in Kazakhstan in 1918-1921. The study is based on the principles of historical, scientific objectivity and systemic structural-functional analysis. For this reason, the author used such methods as the method of historical reconstruction for the reorganization of the administration of Soviet, party and other local bodies; the method of isolation for the study of local (regional) features in relation to local phenomena and processes in the energy sector; the method of typology, which made it possible to identify and describe different types of local authorities. The authors come to the conclusion that in 1918-1921, during the period of civil resistance, "war communism" and the beginning of the Chamber of Commerce and Industry, bodies of the new Soviet power appeared and operated in Kazakhstan. They are characterized as having an anti-democratic character; strict social orientation; alienation of indigenous peoples; immanent nature for creating conflict situations; choosing non-optimal ways and means of solving a problem situation; unification of party and state. As a result, an overgrown and clumsy class of party classification was formed, which was not provided for by the Constitution of the USSR.

Main problem: recently, much attention has been paid to energy saving in production, especially when it comes to industrial units that burn fuel. There are several ways to maximize the use of the heat released during the combustion process, for example, to reduce the temperature of the flue gases at the outlet of the unit, by maximizing its use, both in the technological process itself and by installing additional heat-receiving units, for example, air heaters or other heaters. Another way to save money is to reduce heat losses through the lining of these high-temperature units. Metallurgical units that consume a large amount of energy and fuel require an analysis of their consumption, and ways to save their consumption based on the results of the analysis. Purpose: this article considers the possibility of replacing the existing inner insulation layer of the second and third sections of a high-temperature unit - a metallurgical furnace, with a new one with better technical and economic indicators. Methods: the possibility of replacing the existing inner insulation layer of the second and third sections of the high-temperature unit with a new one, with the best technical and economic indicators, was considered. The calculation of heat losses by thermal conductivity through the side surfaces and the roof with new insulation was performed, and the economic efficiency of the proposed solution was proved. Results and their significance: replacing the existing inner layer of insulation - refractory concrete PHLOCAST M30 (thermal conductivity coefficient from 1,4 to 1,45) with the proposed CERALIT GUN HK 70070 (thermal conductivity coefficient from 1,03 to 1,12) will reduce heat loss to the environment, and thus to reduce fuel consumption for the furnace.

In Kazakhstan, within the framework of the Program «Development of domestic value and export-oriented industries», new modern dairy enterprises are being actively modernized and new modern dairy enterprises are being created, where membrane processes are being introduced to concentrate the components of milk. This is necessary for the rational and integrated use of raw materials, including through the processing of secondary resources, the main of which is whey. Improving the production processes of traditional food products and developing innovative ones is possible only with the use of the latest technologies and technological equipment. Membrane processes are widely used for the use of fractionation and concentration of liquid dairy products, which allows for a new solution to the processing of raw materials and opens up opportunities in the development of new types of food products. The article is devoted to the issue of production and processing of whey in Kazakhstan. The main types of membrane technologies and the advantages of their use in the dairy industry in the Republic of Kazakhstan are considered. The role of membrane technologies in the processing of whey is substantiated, various methods of introducing membrane processing methods to ensure the demineralization of whey, obtaining products with high biological value and consumer properties, reducing the cost of energy carriers, reducing the volume of raw materials in order to save transport costs, non-waste processing of milk solids, recycling water are described. This article analyzes the problems of using resource-saving membrane technologies in the production of dairy products in the Republic of Kazakhstan, ways to solve existing problems associated with increasing the economic efficiency of enterprises. The favorable impact of the use of membrane technologies on the social and environmental aspects of whey processing in the country is substantiated.

In order to successfully conduct agricultural work and obtain a competitive harvest, it is mandatory to carry out spraying operations of crops that require highly qualified personnel, expensive equipment and suitable weather conditions. The use of tractors for spraying fields is the most common solution available at the moment, has disadvantages: high cost, risk of damage to the crop by "hitting", "hooking" or otherwise; environmental damage; due to exhaust gases, the demolition of the solution increases with increasing speed. Using a device designed specifically for spraying equipment is an ideal solution. The purpose of the article is to develop a working model of an automated sprayer for processing agricultural crops. The methods used are: technical justification of a controlled device for processing agricultural crops. Calculation of functional capabilities, algorithms of operation of the proposed automated device: selection of the type of sprayer, engine, chassis, controller, battery, as well as justification of the possibilities of using alternative energy sources (wind energy, solar energy); development of a 3D model of an automation device for anti-weed processing of agricultural crops, printing of parts, assembly of mechanical and electronic parts. Making a prototype using 3D printing; development of the wiring diagram of electronics, software (firmware of the microcontroller; application that controls the settings), testing of the prototype, assembly of the current model; rationale for the optimal use of Arduino and Raspberry Pi boards in this device in a pair: Raspberry Pi will allow you to control processes on the Arduino and easily interact with the Internet when the Arduino itself will perform simple operations such as interacting with electronics and reading sensor readings. The manufactured operating model showed compliance with the goals, a high degree of controllability, environmental friendliness, reduction of energy consumed, labor resources and can be used to scale this device. The developed model of the automation device for anti-weed treatment of agricultural crops can be used not only in agricultural pollination, but also as a mechanism for studying soil parameters: humidity, mineralogical composition and chemical content in the ground, using electronic sensors, as well as an automated mobile platform for any purpose requiring accurate navigation through the territory.

The present stage of development of power systems is characterized by the need to increase their intelligence, that is, the formation of an environment capable of solving the problems of effective management of all components included in the power system. One of the features of modern energy systems is an active consumer, that is, a consumer who has the opportunity to optimize the schedule of loading their capacities, planning energy consumption, intellectualization of energy consumption. In addition to the fact that there are digital systems for collecting, processing and presenting information, as well as transmitting this information via the Internet, to solve the most difficult task of managing power systems, it is necessary to develop a large number of models adequate to real processes that can describe the processes taking place in the power system under consideration. The purpose is to develop models capable of adequately describing the interrelated processes occurring in the considered elements of the power system, as well as in the aggregate of related elements; development of methods that allow solving problems of effective control of elements of energy systems on the basis of the proposed intelligent models. To solve the problem of increasing the intelligence of the power system, nonlinear adaptive models of electrical complexes of an energy-intensive enterprise included in the power system were developed on the basis of balance equations and artificial intelligence methods. The production of alumina with the properties of inertia, nonlinearity and closure is chosen as the production under consideration. This type of production was chosen as the most difficult to predict due to the unpredictability of changes in energy consumption during the transition to other modes of its operation, associated, for example, with the receipt of raw materials with a different chemical composition for processing. Static and dynamic models of energy consumption of electrotechnical complexes with continuous inertial nonlinear closed production based on artificial intelligence methods have been developed, which makes it possible to eliminate the need to use long time series of retrospective data. For the considered type of continuous energy-intensive production, dynamic characteristics of energy consumption and technological processes are obtained from the main controlled parameters, which make it possible to predict emergency situations and partly man-made disasters. On the basis of a genetic algorithm, a multiparametric optimization problem of energy management of continuous production has been solved, taking into account technological parameters and cost factors.

The article contains the results of a research work devoted to an important problem - the development, production and delivery to the consumer of fermented dairy products of a healthy diet fortified (enriched) with milk protein, a vitamin-mineral complex, and probiotics and prebiotics. Purpose is based on mathematical modeling of experimental data, to determine an effective fermented food system for use as the basis of a fortified (enriched) curd product for a healthy specialized diet; to develop a recipe and technology for its production; to study the nutritional, biological and energy value of a new product. Modern technologies and equipment were used in experimental studies: ultrafiltration, fortification, etc. The studies were carried out by standard physicochemical, microbiological methods in three to five repetitions. Mathematical and statistical processing of experimental data was carried out using the program "Statistica-6.0". A recipe and technology for the production of a curd product for a healthy specialized diet has been developed. Its nutritional, biological and energy value has been studied. The developed recipe and biotechnological parameters for the production of the curd product were tested in the industrial conditions of the leading enterprise JSC "Lyubinskiy MKK". The quality and safety of the curd product was studied in the laboratory of techno-chemical control of FGANU "VNIMI" (Moscow).

Main problem: At the present stage of life, Innovations in the financial sector contribute to the optimization of financial intermediation and, in turn, stimulate economic growth. Financial innovations increase the efficiency of the allocation of savings capital to investment capital, as well as increase liquidity in the markets. As the digital economy has developed, the functionality of traditional large financial institutions has been partially replaced by financial technologies (FinTech). FinTech involves the convergence of traditional financial services with mobile services, social media services, big data aggregation and processing, and cloud technologies. Purpose of this article is to identify the main directions of the electronic financial services market in the Republic of Kazakhstan, identify the main problems and prospects for the development of the financial sector of the economy. Methods: The work used general scientific methods of comparative system, vertical and horizontal analysis, structural and functional method, analytical techniques, economic and statistical research methods. The results and their significance: the authors identified the main directions of digitalization of the financial sector of the modern economy, noted the role of FinTech companies and services in both theoretical and practical terms, and provided relevant approaches to the definition of this concept in the economic literature. The main reasons and factors for the development of this direction of digitalization of the financial sector are substantiated, including the concept of financial accessibility, the advantages and disadvantages of FinTech, various approaches to their classification, country and regional characteristics, and an analysis of development trends. The crowdfunding direction of FinTech is noted, approaches to its definition and classification are given, the advantages of the crowdfunding mechanism are revealed, and its role in the modern economy is analyzed. The trend of algorithmic trading development as the most important direction of digitalization of the financial sector is investigated. A detailed analysis of mobile financial services as one of the fastest-growing areas of FinTech is carried out, approaches to their classification are given, factors stimulating the growth of mobile payments, country and regional characteristics are substantiated. The main directions of digitalization of the insurance sector are analyzed, reasonable conclusions about the advantages of InsurTech are made.