The article discusses a way to increase the efficiency of automobile operation by improving methods for ensuring the operability of electrical equipment based on the diagnosis of generators by output voltage. As a diagnosis, it is proposed to perform a spectral analysis of the generated voltage in idle mode and to determine the state of various generator elements from the results. The effectiveness of the proposed solutions is determined by the non-separable diagnostics of the generator, which, based on a thorough examination, can determine the state of various elements of the generator. This method does not require taking the generator out of operation, does not depend on its design and can be used in difficult operating conditions to obtain preliminary information about the state of the generator at the initial stage of maintenance.

The article is devoted to the theoretical analysis M. Doychu species conflicts, conflict structure, developmental stages of the conflict, is also considered rigidity and its ability to influence various spheres of human activity. An analysis of the theoretical material concluded that the performance of the enterprise is important to good social and psychological climate and psychological safety of all participants in the activities of the enterprise.

This article discusses the possibility and practice of Kazakhstani enterprises producing chemical products and raw materials, which are oriented to export regulations REACH, adopted by the European Union that will greatly increase the safety and competitiveness of domestic production.

This article discusses some of the problems of chemical safety, such as the recycling of waste production, chemical accidents and disasters, environmental pollution and the negative effect of the chemical industry on human health, as well as methods for safer handling of chemical products.

In the article different methods of diagnosis of failures of electric equipment which are most often found in the industry today. The classification of methods for diagnosing motor failures is presented, and the advantages and disadvantages of existing methods for diagnosing failures in electric equipment are revealed. Based on the description of the methods of diagnosing electric equipment failures, a comparative table was compiled. Analyzing the comparative table of methods for diagnosing failures of electric equipment, the most current method for diagnosing the technical condition of the electric motor was determined.

The article is concerned with the analysis of fires in the multi-storey residential houses in Pavlodar. The analysis was carried out on statistical data from 2014 to 2016. Examples of fire analysis in Russia are given.

The main directions of increasing the reliability and electrical safety of power distribution networks are considered in the article. The schemes of the main directions of development and improvement of electric grids are given.

In this article, the migration processes and their influence on socio-economic development of the Pavlodar region are considered. The concept of migrations, factors and types of migration are highlighted.. The demographic cases in the region are studied for research of migration processes and their influence on socialand- economic development of the Pavlodar region. Impact of migration on social-and-economic development of the country can be both positive and negative. The account of these factors is important for adjusting of migration processes and optimal policymaking in this sphere.

The article presents new tools for managing labour safety to conduct behavioral safety audits, transforming meetings and labor protection councils into cascade committees, to implement technical and safety standards, and to use new assessment and motivation system and methods of internal incidents investigation.

The work analyzes the emergency situations that occurred on the territory of the Pavlodar region. The main causes of emergencies of natural and man-made nature are presented. The article contains the results of the analysis of the effectiveness of management in a safety-related system in the Pavlodar region and recommendations for improving the safety-related system during the emergency relief operations.

The analysis of the current management system of labor protection at «Aluminum of Kazakhstan» JSC is provided. Services and departments providing production activities are presented. The basic principles of the management system of labor protectionare considered. The organization of work on labor protection and development of corrective and preventive actions are presented.

This article considers chemical safety as a system of measures aimed at protecting vital human interests against adverse chemical effect from threats of processing, storing and destroying hazardous chemicals. Chemical safety is ensured by a complex of legal, organizational, financial, material and informational measures intended for prevention and elimination of real and potential security risk, mitigation of their consequences.

The article is devoted to the current problem of quality control and safety of dairy products. The article provides a generalized description of the system models, discusses the main problems and advantages in implementing the quality control system in small and medium-sized dairy enterprises.

The article is devoted to risk analysis, methods of ensuring dairy products safety. Furthermore, the author dwells on such tool of quality control as a decision tree. The article presents the plan of HACCP for a diary enterprise on an example of the production a sour cream with 15-20 % of fat content.

The possibilities of using controlled transformer-type shunt reactors at power grid substations to optimize the transmission mode are considered. The laws of voltage regulation, providing the mode of natural power and reduction of active power losses in the electrical system, are highlighted. Key words: energy complex, controlled transformer-type shunt reactor, voltage stabilization, thyristor voltage controller, control winding.

Аt present, dairy enterprises use a system for analyzing and monitoring critical control points, as well as a quality management system, to produce high-quality and safe products. These systems take into account factors that may affect the production process and other components by identifying hazards from the procurement of raw materials to the consumption of products for food. The purpose of the article is to study the role and necessity of applying quality and safety management systems at dairy enterprises and reducing the risk at all levels of production

The article describes the relationship of man as a species with nature. It is shown that this relationship is determined by the conditions of existence, the quality of air and water, the necessary elements of nutrition. It is also pointed to the role of environmental conditions-optimal for the body, determining human health and life expectancy

The article describes the results of the analysis of the state of working conditions at the enterprise and at the site of JSC «Алюминий Казахстан». Deficiencies in the OSH management system have been identified. Measures are proposed to improve working conditions and prevent industrial injuries. These measures will help ensure safe working conditions in the workplace and reduce the risk of occupational diseases

In the work measures on preparation of production personnel for actions in the conditions of emergency situations are considered on the example of Neftekhim LTD LLP. The structure of the control system and its main components were studied, the regulatory legal framework used in industrial safety was described. The possible risks and dangers, as well as harmful substances used in the production of plant products and their effect on the body were studied; the current state of the control system in the field of emergency prevention was evaluated

During the preparatory activities for the preparation and conduct of the KShU, the civil defense plans for peace and wartime were adjusted and clarified, the calculations of forces and resources for conducting emergency response activities were refined and their readiness checked. Checked the combat readiness of the units taking into account work in extreme conditions and the provision of personnel with equipped interchangeable clothing. Additional briefings have been organized on compliance with safety measures for fighting fires and performing emergency rescue operations. Autonomous sources of energy supply, stocks of material and technical, food reserves were checked. In general, the forces and facilities of the units of the Service are on daily round-the-clock alert duty and are ready to meet the set tasks for eliminating emergencies and situations at the first alert.

The article is devoted to the task of automating the assessment of the electrical safety level of electrical installations based on the determination of the electrical resistivity of soil layers ρ in specific climatic conditions. The soil ρ value depends on many factors, which can vary significantly during the year. Therefore, the decision was made using modeling based on one of the areas of artificial intelligence: fuzzy logic.

The article analyzes the state and problems of cluster development in the real sector of the region based on the materials of the Pavlodar region. The main problem of innovative development of the Pavlodar region, as well as in all regions of Kazakhstan, in general, is the lack of innovative activity of enterprises, which is reflected in the volume, frequency and efficiency of their innovations. At the same time, most of the enterprises belonging to the real sector of the economy have sufficient resources for the development of innovative activity. However, the prospects for their interaction with enterprises in other sectors and sectors of the economy for the purpose of technology transfer are insignificant, which, in general, doesn’t meet the principles of balanced spatial development of the territory formulated by the program for the development of territories of the Republic of Kazakhstan until 2020. One of the ways to solve this problem is formation and development of a cluster approach and interaction of business entities. The article assesses the efficiency of the cluster’s functioning as an institution of regional development. On the example of the metallurgical cluster of Pavlodar region, the main ways and methods of forming cluster initiatives in the regional economy are considered, a SWOT analysis of the development of the metallurgical cluster of the region is given, and its main problems are identified; identifies priority directions of clusters’ development (metallurgical cluster, including the production of final products, the cluster of railway engineering, agri-food cluster), the realization of which in the region could create the conditions for the emergence and full development of a number of new highly specialized sectors such as cluster chemistry, cluster of road and construction machinery, transport logistics cluster, cluster of modern production technologies and engineering, cluster of manufacturing components for machinery and equipment and cluster of industrial electrical engineering and equipment for power engineering. The authors also noted that the realization of regional development strategies of cluster initiatives can potentially lay the foundations for clusters “future days”, such as: cluster of resource efficiency and environmentally processing, the cluster of new energy, the cluster of innovative medicine, tourism and recreational cluster.

The article describes the results of a study of the effectiveness of the standards being implemented in railway transport. A general view of efficiency and standardization was analyzed. It was studied which document regulates the application of standardization in the Republic of Kazakhstan. Further, the international railway standard IRIS «International Railway Industry Standard» was taken as a basis, which, in turn, is based on the international standard ISO 9001. A study of the methods and types of effectiveness of standards was carried out, as well as an analysis of the applied international standard in the field of railway transport IRIS. The purpose of this standard is to create a business management system that allows for continual improvement, with an emphasis on preventing and reducing delivery defects. It is important to note that the effectiveness of standardization is evidenced by examples showing that ignoring standards turns out to be huge losses for a company for a number of reasons, for example, because its products have not been certified for compliance with a specific standard; due to the additional costs of the company for reworking products that are not manufactured in accordance with the requirements of the standards in the country of export. An analysis of the effectiveness of standardization work in the railway industry can be expressed in relative terms of the effects obtained as a result of the application of the standard: for example, in an increase in the level of safety or in economic growth. The basis for determining the actual effect is the actual level of production that existed at the given enterprise before the introduction of the standard. The measures that can be applied in order to increase the efficiency of solving the problems of developing standardization in the field of railway transport have been studied. Such standardization as one of the elements of technical regulation can provide a contribution to economic growth in excess of the corresponding indicators from the introduction of patents and licenses.

The article is devoted to the mathematical modulation of a complex of experimental data obtained in the process of experimental studies of processed cheese products, processed by mathematical methods. The purpose of this study is to establish the type and amount of the melting salt that promotes the formation of the plastic structure of the processed cheese product. The analysis of scientific research in the field of food technologies showed that mathematical modeling is used in the following areas: clarification of the modes of technological processes, design of recipes and assessment of the quality of finished products, as well as forecasting the shelf life of new products when they are put into production. The most relevant in describing the processes of food production are models of multivariate variance-regression analysis using methods of mathematical planning of the experiment. The authors carried out mathematical modeling and established graphical dependencies characterizing the degree of influence of the regulated factors X1 and X2 on the controlled ones that determine the quality and safety of processed cheese products. It is important that the mathematical analysis of the graphical dependences of the rheological parameters on the adjustable factors indicates the reliability of the data obtained. It is concluded that an increase in the melting salt dose leads to an increase in the – limit shear stress, which reflects the nature and state of the consistency of the processed cheese product. The process of normalization of the controlled factors by the maximum value was carried out. Graphical dependencies were built and regression analysis was performed, the results of which allow an objective assessment of the degree of influence of the type and dose of the melting salt on the chemical and organoleptic characteristics of the test products. The authors have proven that the optimal efficiency of transforming the structure of the constituent components of the recipe into a plastic structure of a processed cheese product that is stable during storage is provided by a combination of adjustable factors X1 (Solva 85) and X2 (Solva 120) taken in a ratio of 1: 1, with a total amount of 1,2 mas.%. At the same time, the quality indicators of the experimental products are characterized by the following values of the controlled factors: У1 – 1280 Pa; У2 – 9 points, У3 – 9,301 (2,0-2,2109 colony forming units /g).

The COVID-19 coronavirus pandemic has brought about a new economic reality, to which every economic entity must adapt, regardless of the scale: within a region, a country, or the whole world. The article examines the regional economic mechanism in the context of the pandemic in the context of the interaction of the market mechanism of self-development and the control influence of the regional authorities. The destabilization of the economic situation in the regions as a result of the pandemic and related restrictions poses the problem of revising the main directions of regional policy To achieve the set goals and objectives, the general methods of empirical and theoretical research were used: analysis, synthesis, induction, deduction, generalization, description. Three spheres play a key role in the economy of Pavlodar region: industry, trade and transport. Just how to remain positive dynamics in terms of industrial production and maintained the services will depend on the development of the region, the main indicators which are discussed in this article through the prism of the events in the context of the pandemic. The necessary health measures taken in response to the pandemic have led to a severe reduction in mobility and are accompanied by high economic costs. The quarantine measures have had a direct impact on businesses, especially microbusinesses. To support this sector, tax incentives were provided, lending was expanded, and measures were taken to further facilitate the business environment. The article reflects only a small list of issues that required changes in the economic mechanism in the context of the pandemic and the introduction of restrictive measures, as well as the strengthening of the influence of external control on the economy. At the same time, the state as whole and individual regions, taking into account their potential and the actual situation in the economy, need to find an optimal balance between the prohibitions and restrictions imposed to ensure the safety of human health and the preservation of the economy in a functional mode, work and income of employees. This problem of finding a balance between prohibitive and permissive measures requires further analysis. At the same time, the state needs to develop and apply tools of a systematic nature, focused on the long term.

The progress of work on the creation of an "intelligent transport system" in Kazakhstan, the development and modernization of the road industry will be reported. The economic and social effectiveness of several transport corridors and new projects were analyzed. Transport corridors of foreign countries, methods of providing logistics services were presented. In his address, the head of state paid special attention to the issues of digitalization of all spheres of life of the population, including the transport sector of Kazakhstan. Currently, the Ministry of investment and development of the Republic of Kazakhstan is working on the creation of an "intelligent transport system" within the framework of the state program «Digital Kazakhstan» (ITS). ITS goal is to systematically integrate transport infrastructure, transport devices and users with modern information and communication technologies aimed at improving the safety and efficiency of the transport process. The concept will include 11 components in ITS. One of them is a special automated measuring instruments (UAVs), which are installed in the main automobile corridors. This device is designed to measure moving vehicles without contact and eliminate unjustified stops. This year, it is planned to put into operation 10 units of RSPP, and by 2020 it is planned to increase their number to 46 units. It is also planned to introduce a traffic management system that will inform drivers about the situation on the roads, a system for forecasting and analyzing climatic conditions, which is carried out through a network of weather stations along the roads, a network of video monitoring and special video cameras for detecting traffic violations, toll road systems that cover the cost of maintenance of the national road network, etc. They will be introduced in stages until 2021. The implementation of this project will reduce road deaths, increase the volume of transit traffic and the speed of logistics services, fully cover the main highways with measuring instruments and create favorable conditions for drivers on the roads. Such systems are already operating in South Korea, Japan, Australia, Europe and the United States.

Fruits and vegetables are most often consumed without being thoroughly processed before consumption. Some plant foods are vacuum-packed to ensure long shelf life as well as preserving the quality and safety of the product. Fruits and vegetables carry naturally occurring non-pathogenic epiphytic microflora on their surfaces. During growth, harvesting, transport and further handling they can be repeatedly contaminated by pathogens from human or animal sources. Fresh fruit crops have been implicated in a number of documented foodborne disease outbreaks. Outbreaks of diseases caused by bacteria, viruses and parasites have been epidemiologically linked to the consumption of a wide range of fruits and vegetables. The aim of our study is to assess the risk of contamination in fruit and berry crops and how to address this long-standing problem, namely, contamination of fruit and vegetables with unnatural pathogenic microflora. The following fruit and berry crops common in Turkestan region were chosen for the experiment: Apple variety Suislepskoe (stolovka) , peach variety Nectarine and grape variety Kishmish. Bacteriological inoculation was carried out by membrane filtration of used sterile water to obtain flushes from the surface of fruit crops. All work was carried out under full aseptic conditions. The utensils, water and other equipment used in the work were sterilised in advance. The data obtained during the experiment shows that there is a potential for widespread contamination of uncharacteristic microflora of plant products. Based on the results of the study it can be concluded that there are yeasts and acetic acid bacteria on the surface of all three samples of fruit and berry crops, which can be universally contaminated food and are not the natural microflora for the above mentioned crops. Specifically, fruits and vegetables can be contaminated with various bacterial pathogens, including Salmonella, Shigella, E. Coli O157:H7, Listeria monocytogenes and Campylobacter.

Currently, close attention is paid to industrial safety at hazardous production facilities. Compliance with industrial safety requirements is directly related to the risks of accidents that can lead to man-made disasters, negatively affect the health and life of the population. As in any other industry, there are problems in ensuring industrial safety. There are several reasons for this: the backlog of standards from scientific and technological progress, the exclusive competence of state authorized bodies, and the lack of a risk-based approach. After the collapse of the USSR, the requirements of industrial safety in the Republic of Kazakhstan have practically not changed: laws and statutory instruments (hereinafter-the LSI) are approved and put into effect, after which they are constantly changed and supplemented; the presence of national and international standards, which, in fact, are revised on the basis of the USSR standards, taking into account the influence of the realities of the time. It can be concluded that the current standards are not focused on the future, scientific and technological progress, innovation, so they are constantly undergoing changes, thereby adapting to the necessary requirements that dictate modernity. State regulation does not contribute to the effective development of industrial safety. This is due to the fact that the state performs exclusively supervisory functions (thus it is exclusively educational in nature), and there is no dialogue between authorized state bodies, expert organizations, scientific organizations, and testing laboratories. If we consider the experience of the Russian Federation in the field of industrial safety, then it makes no sense to accept even some experience, since: similar to the Kazakhstan’ LSI and regulatory and technical documentation (and their constant dynamics), the development of cooperation with the Russian Federation within the framework of the Eurasian Economic Union. Accordingly, it is advisable to consider the experience in the field of industrial safety in Europe and the United States of America because of the effectiveness of regulation and supervision than in the Republic of Kazakhstan and the Russian Federation. This article provides information about international experience in the field of industrial safety in the United States and the European Union. The tasks of state regulation in the field of industrial safety in the Republic of Kazakhstan, the Russian Federation, the United States, and the European Union are described in detail. The analysis of normative-legal acts and normative-technical documentation is carried out. Based on the analysis of international experience, solutions to problems in the field of industrial safety for the Republic of Kazakhstan are essentially presented. The purpose of this article is to reveal the problem in the field of industrial safety in the Republic of Kazakhstan and international experience that the Republic of Kazakhstan can borrow in order to effectively ensure industrial safety. Study of international experience (USA, EU countries, Russia) in the field of industrial safety in terms of: analysis of standards; regulation (control and supervisory functions) to ensure safety. The results of this article will reflect the problems that hinder the effective provision of industrial safety in the Republic of Kazakhstan and essentially suggest ways to solve them.

Currently, the problems of environmental safety are facing society. The industry develops every year. In this critical economic situation, the oil industry is a stimulant for the economic sector in Azerbaijan. The level of development of this industry is also relevant due to other reasons: sociological, technological and features of the economy of Azerbaijan. The production activity of oil processing, concentrating harmful substances and energy, is a source of man-made danger and pollution of the natural environment. The risk management process mainly consists of three stages - risk safety analysis, risk assessment, which is carried out in comparison of calculated and actual risk levels, the so-called acceptable risk levels and the adoption of appropriate regulations and management decisions. One of the factors that should be taken into account when assessing risk and safety is to determine the necessary costs. Since these costs are paid directly to the company, they try to minimize them as much as possible, which reduce the accuracy of risk assessment. One of the objectives of the study is to determine the optimal value of the necessary costs. It is established that the less reliable the method, the lower is the cost of its implementation. The methodological basis of the work was scientific works on these problems of scientists-economists, mathematicians on safety and risk assessment at industrial enterprises. When developing the presented methodology, computational algorithms developed by Dow Chemical were used. This company has collected a large volume of material on accident statistics, taking into account damages. Based on the obtained and experimentally verified data, a system of indices has been developed, an assessment of various indicators for qualitative and quantitative risk assessment of oil refineries. The analysis of the technogenic danger of oil refineries makes it possible to determine ecological and economic losses and choose rational possibilities of acceptable risk. The required costs, depending on the level of risk, are determined based on an increase in the accuracy of calculating the probability of occurrence of the cause of risks. The article examines the relationship between the expected level of risk and economic losses during oil refining in separate technological units, which allow determining the required level of risk and the expected economic damage.

The variety of species and forms of parasites of agricultural animals and the features of their life cycles are the basic foundation for the production of different types and medical forms of antiparasite medicine. In the treatment of the parasitic diseases of agricultural animals, one of the main factors is that the veterinary doctors have the knowledge on the mechanics, efficiency and the safety for humans and environment of the medicine being used. Taking into account high pathogenicity and resistance of parasitic organisms and their ability to adapt to effect of medicine, it is crucial to permanently monitor the efficiency of the applied anthelmintic drugs, including the new drugs offered by veterinary services. This article will describe the results of the research on pharmacodynamic and pharmacokinetic parameters of «Ivermectinum», «Ivermec», «Aversect-1», «Аvrsect-2», «Аivin» drugs and their methods of application with the consideration of terms of maintenance and immune status of cattle herds in Mayconyr village (Irtysh district, Pavlodar region). A comparative analysis of efficiency of the above mentioned drugs in dehelmintization and treatment of cattle was conducted with the results provided. The recommendations and the restrictions on use of the drugs were determined considering the farm condition. The experimental research of the aforementioned broad-spectrum drugs was conducted strictly following the rules of asepsis and instructions on application. The total number of replacement heifers subjected to the dehelmintization under the method of analogues is 150 units. Anthelmintic treatment was conducted two times a year - in springtime (March-April) before pasturage, and fall time (September-October) before confining the cattle in the stable. Coprological study on intestinal helminthes of the examined cattle was conducted in Irtysh RVL of the Pavlodar regional branch of RVE RVL VCaSC MA RK by ovoscopical, flotation and larvoscopical methods. There is a comparative analysis on the efficiency of avermectin group antiparasitic drugs applied twice a year for cattle dehelmintization. The recommendations on the use of the aforementioned drugs for dehelmentization and prevention of parasitic diseases are provided and the requirements for the use were determined.

An analysis of the mechanical, chemical and pyrogenic impact of the Baikonur Cosmodrome on the environment showed the presence of man-made impacts of the first stages (FS) used on the ecosystems of the impact zones (IZ). This article presents the concept of a controlled landing of spent launch vehicles with liquid rocket engines (LRE) in the expected zones of damage to the ecosystems of the area while maintaining the energy-optimal launch scenario of the launch vehicle. Purpose of the article - development of effective technologies for reducing the anthropogenic impact during launches of promising rockets from the Baikonur Cosmodrome based on theoretical and experimental studies of innovative technologies: reducing the area of impact of parts from launch vehicles; fire and explosion safety, no danger of rocket launchers; controlled descent of used first stages; To solve the problem, it is proposed to create an additional IASM, which will be included in the environmental management system of the Baikonur Cosmodrome. Possible design solutions are proposed based on the evaporation of untreated liquid waste from the tanks of separated parts, their fire and explosion safety, and the use of the obtained vapor-gas mixtures for controlled unloading of separated parts while moving along the landing trajectory to the optimal area. The authors of the article have developed evaluation criteria that characterize the main environmental indicators of the studied areas: fire hazard, soil cover and impact on vegetation are studied for inclusion in the IASM. There are objective requirements and basic rules for the creation of HIASM, which is an integral part of the environmental management system of the cosmodrome.

As part of solving the priority tasks set in the Address of the President of the Republic of Kazakhstan Kassym-Jomart Tokayev, a significant role is given to the development of the food industry, including dairy products. Big tasks are to be solved by branch science in the field of processing raw materials of plant and animal origin using the achievements of bio- and nanotechnologies to improve the quality, biological, nutritional value and food safety. New approaches are needed to organize the complex processing of plant and animal raw materials in order to improve the economic, social and environmental aspects of the production itself, as well as the life of the population of the Republic of Kazakhstan. Despite the extensive range of processed cheeses, it is constantly updated. This is due to the need to meet the requirements of nutritional science, changing consumer demand, as well as the availability of raw materials and considerations of the profitability of a particular type of cheese. The working hypothesis of the research was the assumption that for the melting of raw materials it is possible to use reagents that affect the active acidity of the medium, stabilize the structure, bind moisture and improve the consistency and organoleptic characteristics of the finished product. The article is devoted to the issue of the process of melting rennet cheeses. The purpose of the article is to show that the melting process is closely related to different forms of raw material protein micelles. In this article, the influence of the type and amount of melting salt on the formation of the structure of processed cheese is considered, the rheological indicators of experimental products are determined in accordance with the scoring of processed cheeses. The indicator of water activity (аw) was established, the microbiological parameters of the experimental products were determined.

The production of vaccine preparations before release requires standardization of their immunobiological parameters, especially safety and immunogenic efficacy. An indicator of the immunogenic effectiveness of the lumpy skin disease vaccine is the resistance of vaccinated cattle against the virulent virus. However, according to preliminary studies, the virulent control virus did not always cause clinical disease with characteristic symptoms when infected subcutaneously. The purpose is to develop a biological model in the form of a complex consisting of a pathogenic virus, a method of infection and a susceptible animal to assess the immunogenicity of a lumpy skin disease vaccine. Local cattle, intact from lumpy dermatitis, were used to reproduce lumpy dermatitis and develop the causative agent of the disease. As the initial infectious virus, we used a 20 % tissue suspension of nodules (skin nodules) obtained from cattle that fell ill with lumpy dermatitis in the field in the Atyrau region in 2016. As a viral mass to control immunogenicity, a 20 % suspension of skin nodules and edematous skin tissue at the site of the pathogen injection, obtained after the “refreshment” of the virus in animals, were used. The disease was reproduced by infection with the test suspension of the virus intradermally, subcutaneously, intravenously at a dose of 0.5 cm3 and titration on the skin of the animal. The effectiveness of the biological model was assessed by morbidity, severity of the course and severity of the manifestation of the disease. During primary intradermal infection with a field isolate of the virus, the disease manifested itself in one of three animals in the form of hyperthermia, depression, lacrimation, and the appearance of several nodular nodules in the skin of animals. The refreshed tissue virus caused clinical disease both in subcutaneous, intradermal and intravenous infection. But the clinical signs of the disease were more pronounced with intradermal inoculation of the virus, and with intravenous inoculation, it manifested itself in a more severe form with a fatal outcome. Inoculation of the virus intradermally into different areas of the skin led to the development of an independent skin lesion in each infected point in the form of painful edema, followed by necrosis, the size and intensity of which depended on the dose of the injected virus. This development of skin pathology made it possible to work out a method for determining the virus titer in vivo. The tissue virus obtained from the edematous tissue at the site of the pathogen injection was guaranteed to cause clinical disease in cattle during intradermal inoculation and made it possible to evaluate the immunogenic efficacy of the produced batches of vaccine against lumpy dermatitis.

The process of creating new forms is the key to choosing the combination of different textures for a unique aesthetic effect. Currently, various elements of the interior, including furniture and other decorative additions, are the basis for obtaining emotional balance, which is achieved between the functional purpose of the interior and its artistic and figurative concept. The main task in creating such objects is to create the most comfortable and harmonious atmosphere in the interior, regulating the mental processes of a person, which would cause exceptionally positive emotions and stimulate the creative development of users. The purpose is to consider the features of the use of epoxy resin in the design of interior objects and to study the importance of synthetic resins as a modern material for new ways of shaping in interior design and decoration. The methods used are: the use of formaldehyde resins as a modern, affordable, multifunctional material, the combination of resin with coloring and the use of various textures. Expansion of the range of interior elements in the manufacture of which epoxy resin is used. In this regard, it should be noted that the use of various resin compositions when creating design objects meets consumer requirements and complies with modern and latest trends. In this article, a brief study of such a polymeric material as epoxy resin was carried out. The properties of epoxy resin and how they affect the compositional solution, methods of its modification, and functional aspects of design from the point of view of manufacturing interior elements are described. The technologies for manufacturing modern products for decorative and applied purposes coated with epoxy resin are considered. In the process of researching technologies, a series of experiments are carried out to determine the structure of possible sequential actions, within which a technology will be studied and designed to ensure the safety of a new design product made of synthetic materials, then a constructive logic will be provided in which not only the functional properties of the object will not suffer, but also acquire valuable innovative value

In the dairy market of Kazakhstan, the demand for mass-produced dairy products is decreasing and expanding to innovative fermented milk products for functional nutrition. The main feature of the new technology is multicomponent formulations, which include the main raw materials and biocorrectors, ensuring their high biological and nutritional value. New dessert products are prepared on a dairy or protein basis using vegetable ingredients, fermented with strains of dry starter cultures of direct application or immobilized starter culture Bifimm probio. The purpose is to apply immobilized living cells of pure cultures of lacto- and bifidobacteria as a biocatalyst for the fermentation of dairy-vegetable media. During the study, the method of immobilization of microbial cells in biopolymer gels was used. The most effective method is the inclusion of cells in an aqueous solution of biopolymers with a concentration of 25 %. For immobilization, pure cultures of lactic acid and bifidobacteria were selected in the gel as part of the concentrates "BK-Altai-LS Bifi", "Poleznaya Partiya", "Genesis", "Narine", "Bio-yogurt Vivo", and the main prescription ingredients were selected: milk with a mass fraction of fat of 1 %, 2.5 %, 3.2 %, natural grain additives, jams, juices, nuts. Formulations, technological schemes and production methods, prototypes were developed, quality and safety indicators were determined. Studies have shown the effectiveness of immobilized starter cultures in the formation of fermented dessert products. Out of 20 prototypes with the best indicators, 5 samples were selected, in which the optimal ratio of milk, probio Bifimm starter cultures and biocorrectors averaged 70:20:10. The quality and safety analysis showed that new fermented milk products using immobilized starter cultures have a positive effect of more than -70 % compared to direct-use starter cultures, have functional properties and can be used for healthy nutrition in Kazakhstan.

The present stage of development of power systems is characterized by the need to increase their intelligence, that is, the formation of an environment capable of solving the problems of effective management of all components included in the power system. One of the features of modern energy systems is an active consumer, that is, a consumer who has the opportunity to optimize the schedule of loading their capacities, planning energy consumption, intellectualization of energy consumption. In addition to the fact that there are digital systems for collecting, processing and presenting information, as well as transmitting this information via the Internet, to solve the most difficult task of managing power systems, it is necessary to develop a large number of models adequate to real processes that can describe the processes taking place in the power system under consideration. The purpose is to develop models capable of adequately describing the interrelated processes occurring in the considered elements of the power system, as well as in the aggregate of related elements; development of methods that allow solving problems of effective control of elements of energy systems on the basis of the proposed intelligent models. To solve the problem of increasing the intelligence of the power system, nonlinear adaptive models of electrical complexes of an energy-intensive enterprise included in the power system were developed on the basis of balance equations and artificial intelligence methods. The production of alumina with the properties of inertia, nonlinearity and closure is chosen as the production under consideration. This type of production was chosen as the most difficult to predict due to the unpredictability of changes in energy consumption during the transition to other modes of its operation, associated, for example, with the receipt of raw materials with a different chemical composition for processing. Static and dynamic models of energy consumption of electrotechnical complexes with continuous inertial nonlinear closed production based on artificial intelligence methods have been developed, which makes it possible to eliminate the need to use long time series of retrospective data. For the considered type of continuous energy-intensive production, dynamic characteristics of energy consumption and technological processes are obtained from the main controlled parameters, which make it possible to predict emergency situations and partly man-made disasters. On the basis of a genetic algorithm, a multiparametric optimization problem of energy management of continuous production has been solved, taking into account technological parameters and cost factors.

The article contains the results of a research work devoted to an important problem - the development, production and delivery to the consumer of fermented dairy products of a healthy diet fortified (enriched) with milk protein, a vitamin-mineral complex, and probiotics and prebiotics. Purpose is based on mathematical modeling of experimental data, to determine an effective fermented food system for use as the basis of a fortified (enriched) curd product for a healthy specialized diet; to develop a recipe and technology for its production; to study the nutritional, biological and energy value of a new product. Modern technologies and equipment were used in experimental studies: ultrafiltration, fortification, etc. The studies were carried out by standard physicochemical, microbiological methods in three to five repetitions. Mathematical and statistical processing of experimental data was carried out using the program "Statistica-6.0". A recipe and technology for the production of a curd product for a healthy specialized diet has been developed. Its nutritional, biological and energy value has been studied. The developed recipe and biotechnological parameters for the production of the curd product were tested in the industrial conditions of the leading enterprise JSC "Lyubinskiy MKK". The quality and safety of the curd product was studied in the laboratory of techno-chemical control of FGANU "VNIMI" (Moscow).

The article is devoted to the development of technological parameters for the production of gluten-free pasta, as well as to the study of the influence of physico-chemical factors on the formation of the structure and organoleptic parameters of gluten-free pasta. The authors studied modern approaches to the production of gluten-free food in Kazakhstan. During the study, the main types of raw materials used in the production of gluten-free pasta of functional orientation were identified. For the production of a new product, a reasonable choice of raw materials and functional ingredients was carried out, the formulation and production technology were developed, all temperature and time modes were described, physico-chemical, organoleptic parameters of the new product were studied, a production flowchart was developed. The purpose of the article is to develop the technology of gluten-free pasta enriched on the basis of corn, rice flour and meeting the requirements for specialized food products, with the addition of functional and flavoring ingredients to expand the range of gluten-free products in the Republic of Kazakhstan. In experimental studies, the formula of a new gluten-free paste based on rice and corn flour with the addition of flaxseed flour, soy protein isolate «EdimCo», xanthan gum, dietary fiber (psyllium), Supermak booster was developed. The complex results of organoleptic and physico-chemical parameters of whole-grain flour for the production of new gluten-free pasta are presented. The results of organoleptic and physico-chemical indicators, as well as safety indicators of finished gluten-free pasta are presented. The article presents the technological parameters and time modes of the production process of fresh pasta, including the following basic operations: preparation of raw materials at t = 10 0C, kneading pasta dough at t = 40-45 0C, vacuuming at 40-10 kPa, pressing (extrusion) at 7 min, 10-12 MPa, drying and stabilization at 10-12 MPa, cooling of dried products t = 20-25 0C 4 hours, packaging of finished products at t = 35 0C and relative humidity 70 %.

Development of regulatory and technical documentation for the examination of equipment operating under pressure

Main problem: Monitoring the reliability of the foundation of roads, buildings and engineering structures is an important aspect of geophysical research. Modeling of geological heterogeneities is relevant. Moreover, the use of computer modeling in this problem is associated with computational costs. Purpose: Analysis of the vertical electrical sounding (VES) method for modeling the physical properties of soil and their changes when exposed to elastic vibrations. Methods: To achieve the goal, the vertical electrical sounding (VES) method was used, using a one-dimensional model of the geological environment. The direct VES problem was solved by calculating the Hankel integral. Results and their significance: The study made it possible to model a large number of soil layers using the VES method. The results obtained make it possible to determine the parameters of detected objects and changes in the characteristics of the controlled environment when exposed to elastic vibrations. The significance of the results lies in the possibility of improving the method for modeling the physical properties of soil and taking into account their changes under the influence of elastic vibrations, which helps to increase the efficiency and accuracy of monitoring the reliability of the foundation.